ke.gardens-tricks.com
Information

Booths for dogs

Booths for dogs


We are searching data for your request:

Forums and discussions:
Manuals and reference books:
Data from registers:
Wait the end of the search in all databases.
Upon completion, a link will appear to access the found materials.



DIY dog booth: 60 photos, drawing and instructions

Every dog ​​living in the yard of a private house needs a reliable shelter that will protect from bad weather and help keep warm on a cold winter night. A do-it-yourself dog booth does not require much time from you, nor a large amount of materials, nor outstanding builder skills.



Correct location of the kennel

The location of the booth should be protected from frequent windsto prevent the dog from being blown out. Also, the booth should not be in the open sun so that the dog does not overheat in the summer. The ideal solution would be a bright place next to the shade. To prevent the formation of puddles under and near the booth, the kennel is placed on a hill. During the rainy season, constant humidity will lead to the formation of dampness in the booth, which will adversely affect the health of the animal.

It is very important for dogs to see and control everything around, so their housing is installed so that the viewing angle of the yard and house is the broadest... The entrance gate to the site must be visible. Otherwise, the pet will be constantly restless or find itself another, less comfortable resting place. Large dogs are best kept in an open-air cage with a booth. The aviary will allow you to isolate the dog from the yard, but at the same time it will see everything that is happening around. Regardless of whether it is a solid fence or with gaps, it is better not to install the booth where other people or animals often walk. There should be as few irritants as possible so as not to provoke the dog to bark. Constantly barking dog causes inconvenience to people around and owners.


Dimensions of the dog house

At the first stage of building a house for a dog, you need to decide on its size. They depend on the size of the pet. An animal can be one of 3 types.

Practice has shown that the following parameters are suitable for each type of dog:

  1. The size of the booth for small dogs such as pug, terrier or spaniel, width 55 cm, length 70 cm and height 60 cm. The size of the manhole is 30 by 40 cm.
  2. For animals of medium size, such as Shar Pei, Foxhound or Basset Hound, the size of the booth is 75 cm wide, 120 cm long and 80 cm high. The size of the manhole is 35 by 50 cm.
  3. A booth for dogs of large breeds, which include Alabai, Mountain Dog or Dalmatian, width 100 cm, length 140 cm and height 95 cm The size of the manhole is 40-50 by 60 cm.

The actual sizes of the animal and the table are not always the same. If the booth is being made for a puppy that is still growing, you can use tabular measurements.

The dimensions of the booth vary depending on the actual dimensions of the animal. Some animals have non-standard dimensions, in such cases it is better to take individual measurements. The pet's ribcage should pass freely into the hole. The Alabai breed is distinguished by its large dimensions. The dimensions and drawing of the booth for the alabai are determined only after taking measurements from the animal.

When making calculations of the manhole, it is worth measuring the dog's chest and adding 5-8 cm. The height of the manhole is equal to a value that is less than 5 cm of the animal's height at the withers. The maximum depth and vertical dimension make it 5 - 8 cm more than the height of the dog at the withers.


The simplest solution and step-by-step recommendations

A novice home craftsman first needs to visually imagine the structure that he wants to create. Excessive fantasies for a novice builder usually end when he starts drawing up a drawing, drawing or sketch.

The product, especially if it is the first one, should be planned to be simple, understandable in execution, simple rectangular shape, with a central entrance, lean-to. First you need to understand that the shape of the booth is an ordinary closed box with a lid.

Drawing of a dog house with dimensions

The floor is made first

  • This is a shield with the internal dimensions of the length and width of the booth, but with the addition of 12 cm to the length and width. On a flat table, four beams are stacked in the form of a frame. You can connect them together on metal corners.
  • On one side, waterproofing is attached to the frame - roofing felt, roofing felt, glassine. There are two dozen more brand names, but you can choose the cheapest option. You can use a stapler for fastening, you can nail in thin strips so that the roofing material does not sag.
  • Immediately after filing the insulation, two or three beams are nailed along or across the frame. It is better to paint them or cover them with bituminous mastic - they will stand on the ground, and the coating will save them from rapid decay.
  • The frame turns over, insulation is placed inside it. You can cover the insulation, if it is glass wool or other dusty material, with any insulating film. Further, a continuous boardwalk is made of grooved boards with a thickness of 30-40 mm.

The next step is to make side shields.

  • They are made in the same way as the floor shield, but boards with a thickness of 20 mm are nailed to the frame, and the insulation and insulation are not yet inserted.
  • The length of both side shields is equal to the length of the floor, and the width is equal to the inner height of the kennel.
  • The sides are installed on the floor flush with its edges and fastened together with self-tapping screws or corners.
  • It is better to lay the structure on its side for fastening.
  • The side walls are installed strictly vertically in level and temporarily fixed from above with slats or boards between themselves.

Then the back wall is made

  • The manufacturing procedure is the same as for the side ones, and the dimensions should be removed from the already finished place for the end shield.
  • The assembled end wall is inserted into the overall product and fastened with the side ones.

Front part

  • The front face has only one additional difficulty: the access door. The manhole frame is made separately, taking into account the possibility of its insertion into the front wall and fastening to it.
  • In the future, in front of the booth, it is sheathed with boards taking into account the manhole and is installed between the side panels with the part sheathed with boards inward, like the previous parts.

  • The last cover is made - an exact analogue of the floor without insulation.
  • It is installed with the sheathed part down and fastened to the side and end walls with self-tapping screws and flat furniture corners.
  • On such a structure, the slope of the roof is arranged from the used roofing materials. Allowed without bias at all.

The best way: put insulation in the roof frame similar to the floor, and then close it on top with a sheet of waterproof plywood 12-16mm thick. The size of the cover can be significantly wider and longer than the roof, providing the necessary overhangs, shade canopies, a dog rest area and excellent weather protection for the entire structure.

Side walls

  • They can be insulated according to the principle of the roof and ceiling, and then sheathed with plywood or other materials.


Doghouse heating

Heaters that provide high-quality and safe heating for a doghouse must meet a number of requirements: quiet operation, durability, low-temperature regime and heating efficiency. To a certain extent, panel heaters, film thermal insulation and cable underfloor heating have the declared parameters.

Panel heater

The most popular and easy-to-implement DIY heating method is the installation of a panel heater. Electric infrared panels allow you to maintain optimal temperature values ​​inside a dog's home without much expense for electricity and insulation.

Distinctive features of using a panel heater in a dog kennel:

  • quiet operation
  • compactness of the equipment - the standard thickness of the heating model is 2 cm
  • heating temperature no more than +50 ° С - due to moderate heating the air is not "burnt" and there is no need to cover the device with a protective wooden grill
  • ease of installation - the panel is fixed to the surface with self-tapping screws
  • resistance to humid environment - degree of protection against moisture IP66
  • the presence of fire-prevention characteristics allows you to operate the heater around the clock without observing the kennel.

An infrared heater for warming a doghouse operates on the principle of thermal radiation - first, objects are heated, which in turn transfer heat to the air.

High-tech models are equipped with a thermostat placed inside a protective metal box with a lock.

Film thermal insulation

Infrared film is an ultra-thin heater, the work of which is based on the radiation of infrared waves. The heating element distributes heat evenly, preventing the animal from overheating.

A low-temperature film heater, regardless of the manufacturer, consists of three elements:

  1. Heating element - converts electrical energy into heat.
  2. Foil - promotes an even distribution of heat over the entire surface to be coated.
  3. Laminated double-sided PET film - provides insulation and protects the internal components of the system from mechanical damage.

A warm dog house with IR foil heating has several advantages:

  • economical power consumption
  • "Healthy heating" - the length of the infrared radiation of the film coincides with the wavelengths emitted by animals, which increases the immune functions of the animal's body
  • high level of heat transfer - due to the even distribution of energy, there are no "cold zones"
  • kennel heating foil does not change the air humidity.

The main disadvantages of the systems are the high cost of insulation and the complexity of installation. The installation technology provides for covering the film heater with a protective coating.

The entire do-it-yourself installation process can be broken down into several stages:

  1. Surface preparation. It is necessary to level the wall - this is an important condition for uniform heating and trouble-free operation. It is advisable to insulate the surface before installing the IR film in order to reduce heat loss.
  2. Film preparation. Cut out the material. The incision is made strictly along the marked lines. Subsequently, the sections will be combined into a single “warm carpet”.
  3. Installation of a film heat insulator:
  • plan the layout, taking into account that the copper busbars are directed towards the rough surface
  • remove 1 cm of insulation from the supply wires and put on the terminal
  • tape the films to the wall, connect and crimp the contacts with pliers
  • close the joints of the wires with insulation.

After installing the thermostat and temperature sensor, cover the walls with plasterboard or OSB boards.

Cable underfloor heating

An interesting option for creating a heater with your own hands is laying heating cables.

To create a homemade heating and insulation system, you need to prepare:

  • thick plywood
  • wooden beams
  • thermostat
  • heating wire (power 80 W)
  • silicone sealant
  • steel wire
  • Scotch
  • sand.

Useful tools: jigsaw, drill, self-tapping screws, nails and a hammer.

Underfloor heating assembly technology:

  1. According to the size of the kennel, cut two rectangular canvases out of plywood. This will be the top and bottom of the floor.
  2. Nail wooden blocks on the bottom. The thermostat must fit freely into the prepared frame.

Place the finished structure in a dog's dwelling, connect the cable and lay a rug for the pet.

Alternative heating

In search of an alternative way to heat and insulate with their own hands, some owners resort to bold, but not always effective methods:

  1. Heating the doghouse with a light bulb. An infrared heating lamp is able to raise the temperature to the desired level. However, the animal runs the risk of overheating or getting burned on a hot appliance. The minimum distance from the lamp to the dog should be 50 cm, but with the standard dimensions of the kennel, this is difficult to achieve.
  2. Autonomous booth heater. As a rule, the devices operate on batteries. Some models are heating pads with a filler that retains heat for a long time. In order for the heater to work and accumulate heat, it is preheated. The battery-powered heating pad can be used in the dog kennel as an addition to the main heating system.

If you wish, you can do the insulation and organize the heating of your favorite pet's booth with your own hands, spending a minimum of money on the work. The technologies of various methods are quite simple and can be implemented within one to two days.

The efficiency of a greenhouse is determined by the cost of construction, ease of use and high returns. For those who have seen enough of ready-made structures from. Further

A competent approach to arranging the roof of a greenhouse or greenhouse saves summer residents from many problems. Some models are provided. Further

Growing crops indoors, you can provide yourself with fresh vegetables and even create an additional source of income. ... Further

Even under the best conditions, the development of greenhouse plants stops when the daylight period decreases. Cumulative time. Further

With all the variety of store greenhouses, the idea of ​​self-assembly of a home greenhouse is still relevant. Especially popular at this. Further

At first glance, the organization of a year-round greenhouse economy does not differ from seasonal vegetable growing. Seems to be enough in a standard greenhouse. Further

To grow seedlings and greenery in a personal plot, it is enough to build a small polycarbonate greenhouse with your own hands. Those,. Further


Watch the video: TV for Dogs! Chill Your Dog Out with this 247 TV and Music Playlist


Comments:

  1. Abbud

    I mean it's your fault.

  2. Aldis

    You have become estranged from the conversation

  3. Turan

    Sorry to interrupt you, but I need a little more information.

  4. Ceneward

    It's a pity that I can't speak now - I'm in a hurry to get to work. I will be released - I will definitely express my opinion.

  5. Renato

    Here those on!



Write a message